Putting new line on a reel sounds simple, but doing it wrong causes many of the problems anglers blame on their reels: twisted line, loose loops, tangles and short casts. A properly spooled reel casts farther and tangles far less.
This guide covers how to spool spinning, baitcasting and spincast reels, how to avoid line twist, what to do with braided line, and how much line to put on.
Before You Start
- Choose the right line. Check the line capacity printed on your reel (for example “8/140” means about 140 yards of 8 lb line). See how to choose fishing line.
- Remove old line. Strip off old, faded or damaged line. Recycle it at a line recycling bin, found at many tackle shops and boat launches, rather than throwing it out, since loose line is dangerous to wildlife.
- Have a few things ready: scissors or clippers, and a pencil or line spooler. A line spooler holds the filler spool and keeps even tension, which makes the job faster and helps prevent twist.
The Arbor Knot
Every reel starts with a knot that holds the line to the spool. The arbor knot is the standard:
- Wrap the line around the reel spool.
- Tie an overhand knot around the main line.
- Tie a second overhand knot in the tag end, close to the first.
- Pull the main line so the first knot slides down tight against the spool, with the second knot acting as a stopper.
- Trim the tag end.
See our guide to fishing knots for more knots you’ll use with your new line.
How to Spool a Spinning Reel
Spinning reels are the most likely to get line twist, so direction matters.
- Open the bail and tie the line to the spool with an arbor knot.
- Close the bail.
- Set the filler spool flat on the floor, label facing up. The goal is for line to come off the filler spool in the same direction the bail wraps it on, and the twist test in step 6 tells you whether it does.
- Keep tension on the line by pinching it lightly between your fingers in front of the reel, or running it through a damp cloth.
- Reel 15 to 20 turns, then stop and let some slack form between the reel and filler spool.
- Check for twist. If the slack line twists or coils, flip the filler spool over and continue. If it hangs fairly straight, keep going.
- Fill to about 1/8 inch below the lip of the spool.
- Cut the line and secure the tag end with the line clip, a rubber band or tape.
Tip: never fill a spinning reel to the very edge. Overfilled spools throw loose loops of line during the cast, which causes tangles and wind knots.
How to Spool a Baitcasting Reel
Baitcasters are less prone to twist because the spool turns as line goes on.
- Run the line through the rod’s first guide and then through the reel’s level-wind guide (the moving guide in front of the spool).
- Tie the line to the spool with an arbor knot.
- Put a pencil through the filler spool and have someone hold it, or use a line spooler, so the filler spool turns freely.
- Make sure the line comes off the top of the filler spool and goes onto the top of the reel spool, in the same direction.
- Keep firm tension by pinching the line with your fingers as you reel.
- Fill to about 1/8 inch below the edge of the spool. Overfilling can make the line rub on the reel frame.
- Cut the line and tie on your lure.
See baitcasting reels and how to cast a baitcaster.
How to Spool a Spincast Reel
- Unscrew the front cover and slide the line through the hole in the cover.
- Tie the line to the spool with an arbor knot and trim the tag.
- Screw the cover back on.
- Lay the filler spool flat and reel while pinching the line to keep tension.
- Fill the spool until it’s full but the line isn’t rubbing against the inside of the cover. Spincast spools hold less line, so don’t overfill.
See our guide to spincast reels.
Spooling Braided Line
Braid is thin and slick, so it can spin on a bare spool and slip when you set the hook or fight a fish. Two simple fixes:
- Add a backing of monofilament. Put a short layer of mono on the spool first, then join the braid to it with a double uni knot. This also saves money, since you don’t need to fill the whole spool with braid.
- Use tape. A strip of electrical tape on the bare spool gives the braid something to grip. Many modern reels also have a “braid-ready” spool with a rubber band or grip ring.
Keep firm tension when spooling braid. Loosely packed braid can dig into itself under pressure and tangle. See braided fishing line and braided vs fluorocarbon line.
Tips for Monofilament and Fluorocarbon
- Fluorocarbon is stiffer and more prone to memory (coiling). Many anglers use it as a leader rather than filling a spinning reel with it. See fluorocarbon fishing line.
- Soaking a filler spool of mono in warm water for a few minutes before spooling can make it more manageable.
- After spooling a spinning reel, make a long cast in an open area and reel it back under light tension to help the line settle.
How Often Should You Replace Line?
- Monofilament: at least once a season if you fish often, or sooner if it becomes faded, stiff, nicked or coiled.
- Fluorocarbon: similar to mono; replace when it shows nicks, abrasion or heavy memory.
- Braid: lasts much longer. Cut off worn sections near the lure regularly, and you can often reverse the braid on the spool to use the unused line underneath.
Always check the last few feet of line for damage after snags and big fish.
Common Spooling Mistakes
- Spooling a spinning reel in the wrong direction, which builds in line twist.
- No tension, leaving loose line that tangles later.
- Overfilling, which causes loose loops and wind knots.
- Underfilling, which shortens your casts.
- Putting braid directly on a slick spool without backing or tape.
Frequently Asked Questions
Which way should line come off the spool when spooling a spinning reel?
The line should come off the filler spool in the same direction the bail wraps it on. Lay the filler spool flat, reel 15 to 20 turns, then let some slack form: if the slack line twists, flip the filler spool over and continue.
How full should I fill my fishing reel?
Fill spinning and baitcasting reels to about 1/8 inch below the lip of the spool. Overfilling causes tangles; underfilling shortens casts.
Do I need backing under braided line?
It’s a good idea. A layer of monofilament backing or a strip of tape keeps braid from slipping on the spool, and mono backing also saves on braid.
How do I stop line twist on a spinning reel?
Spool the line in the correct direction, keep tension while spooling, close the bail by hand after casting, and use a swivel with lures that spin.
How often should I change fishing line?
Replace monofilament and fluorocarbon at least once a season if you fish often, or sooner if it’s faded, nicked or coiled. Braid lasts much longer but should be trimmed regularly.
Final Thoughts
A well-spooled reel casts better and tangles less. Match the line direction to the reel, keep steady tension, use backing or tape under braid, and fill to about 1/8 inch below the lip. Ten careful minutes at home can save hours of frustration on the water.
For more gear guides, see the Fishing Gear hub and how to cast a spinning reel.
